Disclaimer:

Disclaimer: This unit is for researchers only. The unit and literature have not been evaluated by the Food and Drug Administration in the US. This product is not intended to cure or treat any disease. Government health departments and medical associations state that you must consult a medical doctor for treatment of all diseases. Individual results may vary. NOTE: The Canadian Health Protection Branch has issued a Medical Device License (#28294) for The Magnetic Pulser. The MPG is classified as a Class II Medical Device, allowing for sale without a Medical Doctor's prescription.

What is "The Magnetic Pulser"?

The Magnetic Pulser is a professionally designed quality unit, thoroughly tested and guaranteed to operate as per the specifications. The Magnetic Pulser (MPG) is designed to generate an intense (~43,133 Gauss (magnetic field measurement)), momentary (~2.5mS) pulsed DC magnetic field (click here to see the actual waveform).

NOTE: Please do not confuse this unit with permanent/ceramic magnet therapies, or with the EMR (electro-magnetic radiation) producing units!

Through the principle of induction, this magnetic field creates eddy-currents (tiny electrical micro-currents) in living organic material that contain an electrolyte such as saline. Designed to be used with The Silver Pulser or independently. Targets specific areas.

Magnetic Pulse Generator Bob Beck Protocol Item # EE-02  $276.00 ea.

Unique Features:

• Licensed by the Canadian Health Protection Branch as a Class II Medical Device (License#: 28294)

• New Hand-Paddle design. Our pulsing coil has been re-designed into a custom molded plastic enclosure complete with clear identification of the Bio-North (-) Magnetic Pole.

• A unique circuit design allows The Magnetic Pulser to operate without the use of a Xenon flashtube (as did previous designs) allowing for maximum power delivery to the coil.

• Fully Automatic. The MPG4 will automatically charge and discharge - no manual pulsing required. An internal Digital Counter allows the MPG4 to pulse approximately 5-10 minutes between resets.

• LED light bargraph. A light bargraph consisting of five Green LED lights, illuminates sequentially giving visual indication of the MPG4 charging up. A dual function Red LED light indicates either the unit has completed a 5 minute cycle of pulses, or an overload condition has occurred.

• Operates from an AC-DC Wall Adapter (included), or from a 12 Volt DC source like an automobile battery, appropriate solar panel, etc.

• Extremely high magnetic power output. Generates ~32.67 Joules (Watt*Seconds) of energy through the use of a 600uF, 330VDC Custom Photoflash Capacitor. This then produces ~43,133 Gauss (~43 kiloGauss) magnetic field in the coil.

• High-Frequency Custom Switch Mode Pulse-Width-Modulated (PWM) power supply allows for fast charges (3.5 seconds) and a very lightweight unit. Our PWM power supply is a constant-current design.

• Double-insulated practices used throughout to ensure the greatest electrical safety. Coil is completely enclosed in a custom-molded plastic Hand Paddle. No exposed wires or leads.

• New Professional Capacitor. We now have a Professional Custom Strobe type Capacitor designed specifically for our Magnetic Pulser. The manufacturer rates the capacitor at well over a 30 million (30,000,000) cycles of operation. Compare this with our earlier version model MPG2 and MPG3 which had a 250,000 cycle life, or to our MPG1 which had a 85,000 cycle life, or even to photoflash based pulsers that have 5,000 - 10,000 life cycle. Click HERE to see our MPG capacitors.

• Very Fast charging cycle. Unit fully charges in 3.5 seconds.

• Overload Protection. Should an overload or fault condition occur in the charging section, a sensor will limit the current, then eventually shutdown the unit until the fault condition is removed.

• Bio-North Magnetic Pole Polarity (-) or South-Seeking is clearly identified on one side of pulsing coil. This gives the user the choice of applying either Bio-North (-) or Bio-South (+) pole energy to the site.

• Our Electrical Circuit Boards are GOLD Plated for extreme reliability and workmanship.

• Compact and lightweight. MPG4 unit weighs 3/4 Lbs. (0.3 Kg.), Magnetic coil weighs 1 Lb. (0.4 Kg.). Total shipping weight of complete MPG4 with wall adapter weighs ~3 Lbs. (~1.3 Kg.).

The Unit:

The Magnetic Pulser is housed in an attractive ABS "PC-bone" coloured plastic box. A Toggle Switch turns the Magnetic Pulser on and off. A series of Green lights indicates power is available and visually shows unit is charging. When turned on, the Magnetic Pulser will immediately begin to charge up (in about 3.5 seconds). When fully charged, the last Green light will go on briefly, and the unit will immediately discharge the stored energy of the capacitor into the pulsing coil. The Magnetic Pulser will then begin another charge cycle.

Should an overload or fault condition occur in the charging section, the MPG4 will shutdown until the fault condition is removed, and a Red indicator light will come on. After approximately 5 minutes of pulsing, the MPG4 will go into stand-by mode until a physical reset occurs. This helps prevent continuous operation should the MPG4 be left on unattended. A Red light will illuminate.

The Magnetic Pulser is packaged in a lidded cardboard "die-cut mailer" box for easy storage.

Electronics:

The Magnetic Pulser is designed to the highest standards. We have improved on the original design with added features. These changes by no means alter the effectiveness of the unit. Our electronic design is unique and efficient making the unit very reliable and powerful. Early designs required the use of a Xenon flashtube. We've completely re-designed The Magnetic Pulser from the ground up using the latest in electronic components. The result is a very powerful, reliable, rugged unit that transfers more energy to the output coil. In addition, we use double-insulation techniques to ensure the greatest in electrical safety. This is of extreme importance!

Specifications (as measured on a Tektronics TDS 210 Digital Real-Time Oscilloscope, and Wavetek AD105 Clamp-On RMS Ammeter)

• Energy Storage Capacitor: 600uF, 450 Volts DC Click here to see our MPG capacitors
• Typical Energy Storage: 32.67 Joules (Watt*Seconds)
• Maximum Energy Storage: 36.75 Joules (Watt*Seconds)
• Typical Peak Charge Voltage: 330 Volts DC
• Maximum Peak Charge Voltage: 350 Volts DC
• Minimum Peak Current Discharge into Coil: 150 Amps RMS
• Typical Charge Time: 3.5 Seconds
• Pulse Rise Time: <1.8 uS (microseconds) Click here to see the actual waveform
• Pulse Duration: ~2.5mS (milliseconds) Click here to see the actual waveform
• Main Coil Inductance: ~2.5mH (millihenries)
• Flux Density: 40,500 Ampere*Turns
• Peak Magnetic Field Output: 43,133 Gauss (~43 kiloGauss).
• Minimum number of Pulse Discharges 30 Million (30,000,000)

Dimensions:

The Magnetic Pulser is 5.00" wide x 5.25" long x 2.00" high (12.5 cm wide x 13.25 cm long x 5.0 cm high). Casing is high-impact ABS plastic. Weight of The Magnetic Pulser unit is about 3.0 Lbs. (1.3 Kg.) total. Case is "PC-Bone" in colour.

Each Magnetic Pulser comes complete with:

• The Magnetic Pulser MPG4 unit

• All MPG4's ship with an International Wall Adapter intended for any voltage from 110VAC 60 Hz (North America) to 220/240 Volt AC 50 Hz Mains (as found in International Countries). Thus, you can use your new MPG4 virtually anywhere in the world. The AC-DC Wall Adaptor is rated at 12 Volts DC @ 1.5 Amps, centre positive. (NOTE: This wall adapter can be used on The Silver Pulser, or Water Ozonator unit.)
• Cardboard "die-cut mailer" Storage Box
• 2 Year Parts and Labour Warranty

International Voltage (220/240 Volt AC 50 Hz Mains) Requirements:

• All MPG4's ship with an International Wall Adapter intended for any voltage from 110VAC 60 Hz (North America) to 220/240 Volt AC 50 Hz Mains (as found in International Countries). Thus, you can use your new MPG4 virtually anywhere in the world.

• Additionally, the Magnetic Pulser may also be operated directly from a 12 Volt DC Battery like an automobile cigarette lighter. You will need to purchase an adapter cord which plugs into the cigarette lighter and has a Centre Positive, 2.1mm Plug, like Radio Shack® part #270–1528.

Options for Powering the Magnetic Pulser

In the event of a power outage here are some options for powering the Magnetic Pulser:

1. The Magnetic Pulser may be operated directly from a 12 Volt DC Battery like an automobile cigarette lighter. You will need to purchase an adapter cord which plugs into the cigarette lighter and has a Centre Positive, 2.1mm Plug, like a Radio Shack® part #270–1528.
2. The Magnetic Pulser can be powered by a suitable solar panel. Keep in mind that most solar panel generators are used to re-charge a battery which in turn operates the unit. Therefore we suggest you use a solar panel (preferably a sealed Gel-Cel® type) to re-charge a 12 Volt DC automobile battery, then run the Magnetic Pulser directly from the battery. You will need to use a cord which has alligator clips on one end to attach to the battery terminals, and the appropriate Centre Positive, 2.1mm Plug on the other end to plug into the Magnetic Pulser. Be careful with polarity! This type of cord with alligator clips on one end is probably not readily available, therefore you will to need to buy a cord and cut off the end that normally goes into the cigarette lighter, and solder your own set of alligator clips. Use a black and red alligator clips so you ensure polarity is correct each time you connect the circuit.
3. If you wish to operate the Magnetic Pulser directly from a solar panel you will need to use a 12 Volt DC output panel that is capable of supplying at least 2.5 Amps. The Magnetic Pulser's initial starting demands may require a higher output solar panel. That is why it is preferable to use a charged 12 Volt DC battery instead.

What about a Warranty?

The Magnetic Pulser has a full 2 Year Parts and Labour Warranty. A replacement custom main capacitor can be ordered through us.

How much is "The Magnetic Pulser"?

Magnetic Pulse Generator Bob Beck Protocol Item # EE-02  $276.00 ea.

$276.00 US Please contact us for Shipping Charges, Rates, and Options or use our secure shopping cart (Visa, MasterCard, and Discover Card, or Money Order) Wholesale inquiries welcome. Please call 1-866-747-7447 or 541-434-0318 for details.

Other Interesting Alternative Health Products:

Please click HERE for Teslatech's current Products...

Cell Phone Protection | Water Revitalization | Electro-Medicine | Microwater | EMF Radiation Protection | Research Links Home

Copyright 2000,2001 Future Tech Today.

Shipping Policy | Return Policy | click here to reach us info@futuretechtoday.com

No medical advice is insinuated. Any and all medical conditions should be treated by a Qualified Medical Doctor. Not for intended as medical advice. These statements have not been evaluated by the FDA. None of our products are intended to diagnose, treat, cure, or prevent any disease. Please seek qualified medical advice.